Know Your RoofRoof Structure & Shape

Parts of a Roof: How the Layers Fit Together

Last updated

Quick answer

A shingle roof is built in layers. Rafters or trusses hold up the roof deck. Ice and water barrier and underlayment cover the deck, and shingles go on top. Flashing seals the joints at walls, chimneys, valleys and pipes. Vents let the attic breathe, and gutters carry the water away.

In this guide
Underside of a roof overhang with labels pointing to the fascia, gutters, downspout, solid vinyl soffit and vented vinyl soffit.
Under the eave: fascia, gutter and downspout, with solid and vented vinyl soffit.

See every part of the roofline, labeled

The layers, from the bottom up

  1. Framing: rafters or trusses that give the roof its shape and carry its weight.
  2. Roof deck: plywood or OSB sheathing nailed to the framing. Ohio's code requires shingles to be fastened to a solid deck.
  3. Ice and water barrier: a peel-and-stick membrane along the eaves, in the valleys and around openings, where water and ice back up.
  4. Underlayment: synthetic or felt sheets across the rest of the deck, the backup layer if water gets past the shingles.
  5. Starter strip: a row along the eaves and rakes, under the first course, that seals the edge of the first row of shingles.
  6. Shingles: the layer you see. Each row covers the nails of the row below it.
  7. Ridge cap: shingles bent over the peak, usually covering a ridge vent.

The parts that seal the joints

Shingles can't seal a joint on their own, so flashing does it. Step flashing runs where the roof meets a wall, chimney flashing wraps the chimney, valley flashing lines the valleys where two roof planes meet, and pipe boots seal around vent pipes. Kickout flashing sits at the bottom of a roof-to-wall joint and turns the water into the gutter. These joints are where leaks often start.

The roof edge

The eave is the lower edge of the roof, where the gutters hang. The rake is the sloped edge on a gable end. Drip edge is the metal trim along both, which carries water off the edge. Fascia is the board along the edge, and soffit covers the underside of the overhang. Gutters and downspouts carry the water away from the house.

How the attic fits in

Under the deck, ventilation brings outside air in low at the soffit and lets it out high, usually through a ridge vent. Insulation on the attic floor slows heat, and air sealing stops warm air from leaking up. Together they keep the roof deck cold and dry in winter, which limits ice dams and condensation.

Rooftop Relief inspects and repairs every part of the roof for homes in Cincinnati, Loveland and across Greater Cincinnati.

Looking for another word? See the roofing terms glossary, A to Z.

FAQ

Parts of a Roof: common questions

What is the layer under the shingles called?

Underlayment. Along the eaves and in the valleys it's usually ice and water barrier, a peel-and-stick membrane. Under both is the roof deck, the plywood or OSB nailed to the framing.

Which parts of a roof are replaced in a roof replacement?

The old shingles and underlayment come off down to the deck. Damaged decking is repaired, then new ice and water barrier, underlayment, starter strip, shingles and ridge cap go on. Best practice is new flashing too.

Is the roof deck part of the roof?

Yes. The deck is the structural layer the roofing is nailed to. You can see its underside from the attic, which is where stains, frost or soft spots show up.

Still have a question?

Call and talk it through with our team. No pressure, no obligation.

  • Underlayment & Roof Deck

    Underlayment

    Underlayment is the water-resistant layer between the deck and the shingles. It's the backup if water gets past the shingles. Most roofs use synthetic or felt underlayment across the deck, with self-adhered membrane at the eaves, valleys and around penetrations, where leaks are most likely to start.

  • Flashing & Roof Edge

    Roof Flashing

    Roof flashing is thin metal, sometimes rubber, installed wherever a roof meets something else: a chimney, a wall, a vent, a valley. It steers water over those weak spots and away from the roof deck. A lot of roof leaks start at flashing, not in the middle of the shingles.

  • Flashing & Roof Edge

    Eave

    The eave is the lower edge of a roof, where it overhangs the exterior wall. It's where your gutters hang. Fascia, soffit and drip edge all meet there, and because water and ice collect at the eave, it's a common spot for leaks and rot.

  • Attic Ventilation

    Ridge Vent

    A ridge vent is the exhaust vent along the peak of the roof. Air comes in low at the soffit, rises as it warms, and leaves through the ridge vent, so it only works if air can get in at the bottom. Together, the two carry heat and moisture out of the attic.

  • Flashing & Roof Edge

    Drip Edge

    Drip edge is a strip of L-shaped metal flashing along the edges of a roof. It sends water off the shingles and into the gutter, and keeps it from soaking the roof deck and fascia. It's a cheap part that protects wood that rots easily.

  • Underlayment & Roof Deck

    Roof Deck

    The plywood or OSB boards nailed over the rafters that the roof is built on. Also called sheathing or decking.

Need a hand with this?

Inspections are free, and we respond within 2 hours, 24/7.

Free inspection

Ready to protect your home?

Get your free inspection today. Calls are answered 24/7, and we serve the greater Cincinnati area!

Step 1 of 6

What do you need help with?

  • Free roof inspections
  • Fully Licensed & Insured
  • Owens Corning Preferred Contractor
  • 760+ satisfied customers

Prefer to talk? Call (513) 560-1181

Call Now