Know Your RoofFlashing & Roof Edge

Kickout Flashing: What It Is and Why It Matters

Last updated

Quick answer

Kickout flashing is a small angled piece of metal at the bottom of a roof-to-wall joint, where the edge of a roof runs into a sidewall. It turns water out into the gutter. Without it, water running down the step flashing can pour behind the siding and rot the wall. Ohio's residential code requires one.

In this guide

Where it goes

Anywhere the lower edge of a roof stops against a wall that keeps going: a garage roof against a two-story wall, a porch roof against the house, or a lower roof that ends partway along a wall. Ohio's code requires flashing that diverts water away from the wall wherever the eave of a sloped roof meets a sidewall.

How it goes in

  1. The kickout goes on first, at the bottom of the joint, fastened to the roof deck.
  2. Shingles and step flashing lap over it as they work up the wall.
  3. Housewrap laps over the flashing, and the siding covers it, held about an inch above the roof.
  4. The gutter stops just short of the wall, so the kickout can drop water into it.

Why it matters

Water runs down a roof-to-wall joint along the step flashing, and at the bottom it has to go somewhere. A kickout sends it into the gutter. Without one, it runs down the face of the wall and can get behind the siding, into the sheathing, framing and insulation. Siding can hide that damage for years.

Signs it's missing or failing

Look where a lower roof meets a wall. Warning signs are no angled piece at the gutter end of the joint, streaks or stains on the siding below it, soft or swollen trim, peeling paint, and stains on the inside wall or ceiling near that corner. Fixing it is often a roofing and siding repair together.

Adding one to an existing home

A kickout can be added later, but it has to be built into the wall, not stuck on top. The siding and shingles at the joint come off, any damaged sheathing is repaired, and the kickout and step flashing go in with the housewrap lapped over them. Then the siding goes back on. Cutting a slot and sliding a kickout under the shingles isn't a proper fix.

Rooftop Relief inspects and repairs kickout flashing for homes in Cincinnati, Loveland and across Greater Cincinnati.

Looking for another word? See the roofing terms glossary, A to Z.

FAQ

Kickout Flashing: common questions

Do I need kickout flashing?

If any roof edge on your home ends against a wall, yes. Ohio's residential code requires flashing that turns water away from the wall wherever the eave of a sloped roof meets a sidewall.

Why is there rot on the wall below where my roof meets it?

A missing or failed kickout is a common cause. Water running down the roof-to-wall joint goes behind the siding instead of into the gutter.

Can kickout flashing be added without a new roof?

Yes. The siding and a few shingles at the joint are removed so the kickout can go in under the step flashing and housewrap, then everything goes back on.

Still have a question?

Call and talk it through with our team. No pressure, no obligation.

  • Flashing & Roof Edge

    Step Flashing

    Step flashing is a series of small L-shaped metal pieces installed in a stair-step pattern where a sloped roof meets a vertical wall, like a dormer or the side of a chimney. Each piece sits on a shingle course and is covered by the next one, so water runs out over the shingles, not into the joint.

  • Flashing & Roof Edge

    Roof Flashing

    Roof flashing is thin metal, sometimes rubber, installed wherever a roof meets something else: a chimney, a wall, a vent, a valley. It steers water over those weak spots and away from the roof deck. A lot of roof leaks start at flashing, not in the middle of the shingles.

  • Flashing & Roof Edge

    Apron Flashing

    Apron flashing is a long piece of bent metal that seals the joint where a roof slope runs up into a vertical surface, like the front of a chimney, a dormer face or a wall at the top of a slope. It sheds water running down that wall onto the roof, and counter flashing or siding covers its top edge.

  • Flashing & Roof Edge

    Eave

    The eave is the lower edge of a roof, where it overhangs the exterior wall. It's where your gutters hang. Fascia, soffit and drip edge all meet there, and because water and ice collect at the eave, it's a common spot for leaks and rot.

Need a hand with this?

Inspections are free, and we respond within 2 hours, 24/7.

Free inspection

Ready to protect your home?

Get your free inspection today. Calls are answered 24/7, and we serve the greater Cincinnati area!

Step 1 of 6

What do you need help with?

  • Free roof inspections
  • Fully Licensed & Insured
  • Owens Corning Preferred Contractor
  • 760+ satisfied customers

Prefer to talk? Call (513) 560-1181

Call Now